Persistent /dev/tty* names for GPS and Scanse Sweep

This details for this post are stolen from here; I’ve just tweaked it into my context.

The problem it solves is that both GPS and Sweep are USB UART /dev/ttyUSB? devices, and which is which is indeterminate and will change between boots.  The stolen solution below sets up a symlink to each device based upon the device attributes such that the code only ever refers the symlink i.e. ttySWEEP and ttyGPS rather than trying to guess the correct /dev/ttyUSB? underlying these symlinks.  I’ll hand you over now to my edition of the original author’s post:

Persistent names for usb-serial devices

I own a bunch of devices that appear as /dev/ttyUSB? in the system e.g. GPS and Scanse Sweep.  As I plug them in and pull them out from the USB ports, they get names like /dev/ttyUSB0 or ttyUSB1. Sadly the device names are not persistent — whether the Sweep pops up as /dev/ttyUSB0 or /dev/ttyUSB1 depends on the order in which are the devices discovered by the kernel. That makes things difficult — it usually requires a trial and error approach to find out what the hell is the GPS board’s tty name this time.

Wouldn’t it be nice to have persistent, descriptive device name for each of these toys? Like /dev/ttyGPS and /dev/ttySWEEP?

usb-serial devices

To distinguish between them we need some other unique identifier — in this case a vendor, product and serial number. These are the messages recorded at the end of /var/log/messages when Sweep (for example) is plugged in:

May 13 06:22:27 general kernel: [ 30.629485] usb 1-1.4: new full-speed USB device number 5 using dwc_otg
May 13 06:22:27 general kernel: [ 30.756984] usb 1-1.4: New USB device found, idVendor=0403, idProduct=6015
May 13 06:22:27 general kernel: [ 30.757006] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
May 13 06:22:27 general kernel: [ 30.757019] usb 1-1.4: Product: FT230X Basic UART
May 13 06:22:27 general kernel: [ 30.757031] usb 1-1.4: Manufacturer: FTDI
May 13 06:22:27 general kernel: [ 30.757044] usb 1-1.4: SerialNumber: DO004VY5

UDEV rules

Now with the list of identifiers in hand let’s create a UDEV ruleset that’ll make a nice symbolic link for each of these devices. UDEV rules are usually scattered into many files in /etc/udev/rules.d. Create a new file called 99-usb-serial.rules and put the following lines in there:

SUBSYSTEM=="tty", ATTRS{idVendor}=="10c4", ATTRS{idProduct}=="ea60", ATTRS{serial}=="011806AE", SYMLINK+="ttyGPS"
SUBSYSTEM=="tty", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="6015", ATTRS{serial}=="DO004VY5", SYMLINK+="ttySWEEP"

By now it should be obvious what these lines mean. Perhaps just a note for the last entry on each line — SYMLINK+=”ttySWEEP” means that UDEV should create a symlink /dev/ttySWEEP pointing to the actual /dev/ttyUSB* device. In other words the device names will continue to be assigned ad-hoc but the symbolic links will always point to the right device node.

Right back to me – this is a preemptive strike for when I add the Scanse Sweep to Hermione’s existing GPS.  However, that’s not going to happen until the Garmin LiDAR-Lite stops f’ing up the I2C (again), and I’ve tested all the varients of the GPS flight plan code.

Leave a Reply

Your email address will not be published. Required fields are marked *